Billy Bob's Golf | Designer and Manufacturer of Golf Clubs, Parts and Golf Repair Equipment

Featured Products

TaylorMade M1 (2017) Slider Head Weights

TaylorMade M1 (2017) Slider Head Weights

 

   Billy Bob's had many request for the New 2017 TaylorMade M1 Slider Head weights.

 The 2 weights are used in the sole of the club to adjust Ball Flight Variations and Weight Preferences. 

They are available in 6 different gram weights: 7, 9, 11, 13, 15, 17

You can also double up the slider weights to add more weight and change many different combinations.

                                      Please Note* Do not tighten the weight screw so tight it can strip the threads. Snug tighten only

                          

M1 2017 SLIDER WEIGHTS 7g

$15.99 (save 36%)

TaylorMade M2 (2017) Head Weights

TaylorMade M2 (2017) Head Weights

 

Billy Bob's had many request for the New 2017 TaylorMade M2 Headweights.

 The weight is used in the sole of the club to adjust the swing weight due to shaft changes also adjusting flight varations and weight preferences. 

They are available in 10 different gram weights: 2, 4, 6, 8, 9,10, 12, 13, 15, 18

                           *NOTE: 12g to 18g weights are made from Tungsten and are little higher in price.

M2 2017 HEAD WEIGHTS 2g

$14.99 (save 40%)

Callaway 2016-2017 and New EPIC Sub-Zero Driver Weights

Callaway 2016-2017 and New EPIC Sub-Zero Driver Weights

  We had to Revised the Heavier Callaway Aftermarket Weights for the New 2017 BBG Epic Sub Zero (Driver Only) & Fusion Fairway and Last Years Versions 2016 GGB Double Black Diamond, the XR 2016 Sub Zero, XR Pro, Great Big Bertha 2015. 

  We are making the heavier weights in Tungsten, because the old-style shank was too Long and didn’t fit some of the lower profile heads, they now fit all of them with no problem. The Tungsten weights are little more money but worth it.

  They are available in 2, 4, 6, 8, 9.5, 11, 13, 15, 17 Grams which is more than the factory is offering. With many different head weights, you have combinations for Fade, Draw and Swing Weights Adjustments.

 

Callaway 2016 Head Wt 2g

$11.99

Callaway 2017 Epic Slider Head Weights

Callaway 2017 Epic Slider Head Weights

Billy Bob's had many request for the New 2017 Callaway Epic Big Bertha Driver Slider Head weights.

 The weight is used in the sole of the club to adjust the swing weight due to shaft changes and adjusting flight variations and weight preferences. 

They are available in 7 different gram weights: 6, 8, 10, 12, 24, 28, 30  Note* We  recently added 24 Gram

AS PICTURED 16g STOCK WEIGHT & 6g ADDED WEIGHT = 22g.

Please Note *  We Now Have the Heavier Weights since they are molded Tungsten they are more expensive.

Factory Stock Weight is Approx. 16.5 Grams also these are molded metal parts and can vary  - + .03grams

EPIC SLIDER 6g

$24.00 (save 14%)

Callaway 2017 EPIC Sub-Zero Fairway Woods & Big Bertha Fusion Driver Head Weights

Callaway 2017 EPIC Sub-Zero Fairway Woods & Big Bertha Fusion Driver Head Weights

  We are now making the Headweights for the 2017 Callaway Epic Fairway Woods and the Great Big Bertha Fusion Driver all .

  They are available in 3, 6, 9, 12, 14, 16, 18, 26, 28 Grams which is more than the factory is offering. With the many different head weighs you have many different combinations for Fade and Draw and Swing weights. 

Click on upper Tab:  Images & Specifications to see the clubs they fit !!

EPIC F 3g

$15.00

CMX® Hot Melt Glue Weight System

CMX® Hot Melt Glue Weight System

 

  This is the New CMX® Billy Bob Hot Melt System

  This is the System that's used in the Tour Vans and the Large High Volume Custom Repair Shops, its not something you get from you local hardware store, nor is the Hot Melt Glue packs it comes with. This is used for weighting Heads and allowing you to place the weight in certain places in the head, this adjust the MOI and Center of Gravity, it's also used for damping the sound if you want, depending on the glue placement inside the head. The gun comes with special glue packs that are specific for these applications.

There are two types of Tip Nozzles Straight and Curved which are Sold Separately. The gun comes with standard nozzle but we don't recommend it for proper glue placement insde the head.

Note* Photo shown with straight Tip not included.

 

CMX Hot Melt Glue System

$475.00 (save 19%)

NEW Cool Gel  Heat Protection

NEW Cool Gel Heat Protection

Billy Bob's uses Cool Gel

 We use this Product for those touchy situations that involes HEAT...  If you want to protect those $500.00 Delicate Composite Heads without damading the rubber seals and removing the shafts with out damaging the club Finish, or saving those ferrules... or damaging those anodize adjustable Sleeves, this is a product you need to have in your shop...$29.00 a small Price to pay instead of $400.00 or $500.00 Mistake.

Cool Gel

$24.99

NEW 3M 810 Epoxy NS Tan

NEW 3M 810 Epoxy NS Tan

   We have found that this Acrylic adhesive 810 NSTan  non-sage (better adhesion) is the best epoxy that is available.... it is use by PXG exclusively , it has an unbelievable sheer strength...  10 min work time and can be hit  with full strength in 30 Minutes, the problem is that it is very expensive use only on the clubs that need to be bullet proof.

This come in a 1.7 cartridge and you well need the the Billy Bob's  Epoxy Cartridge Gun is the easiest way to dispense epoxy using 1.7 oz. cartridges or 50 ML cartridges. The gun will dispense 1:2 or 1:1 mixing ratios, there is no need for changing plungers. Also we have found that dispensing the epoxy without the mixing tips easier. Put the epoxy straight on to the mixing board, wipe the tip clean and install the cap back on the cartridge. This saves the cost of buying mixing tips and uses less epoxy. Be sure to mix the epoxy thoroughly.

 Also please note that you may want to clear the nozzle with a pick or all. Remove any harden epoxy in the nozzle when removing the cap. This will assure a clean flow of epoxy.

Epoxy 3M 810 Tan

$28.99

TaylorMade M1 Drivers 2017 460, 440 + Shaft and Grip

TaylorMade M1 Drivers 2017 460, 440 + Shaft and Grip

Let us Custom Build Your New M1 Driver

The all-new M1 driver takes multi-material construction to the next level to deliver distance, forgiveness and complete personalization. Featuring a new 6-layer carbon crown and additional carbon toe panel, the 2017 M1 driver has 43% more carbon than last year’s model. The additional focus on multi-material construction saves weight to enable lower CG for better launch conditions and allows for an expanded T-Track for improved adjustability.

  TaylorMade engineers relied on proven internal acoustic management techniques and modified them as necessary to meet the demands of new materials and shaping. The result: the re-definition of best-in-class sound by controlling vibration and pitch at impact. Combined with external performance technologies, TaylorMade has delivered maximum distance and forgiveness through multi-material construction and complete personalization for every swing.

  Additionally, the iconic two-tone crown of the M1 driver is precision-fit to the skeletal titanium body using an FF2FF process—a breakthrough engineering technique that results in craftsmanship of the highest quality with manufacturing repeatability for a consistent, aggressive appearance and undeniable performance.

HEAD LOFT LH LIE VOLUME    
M1 460 DRIVER 8.5° NO 56° - 60° 460CC    
M1 460 DRIVER 9.5° YES 56° - 60° 460CC    
M1 460 DRIVER 10.5° YES 56° - 60° 460CC    
M1 460 DRIVER 12° NO 56° - 60° 460CC    
HEAD LOFT LH LIE VOLUME    
M1 440 DRIVER 8.5° NO 56° - 60° 440CC    
M1 440 DRIVER 9.5° NO 56° - 60° 440CC    
M1 440 DRIVER 10.5° NO 56° - 60° 440CC    

On Your order... list shaft and grip and we will call you with Quote also ask for our specials on custom shafts 20% OFF .

List your custom shaft and grip

M1 Driver 2017

$380.00 (save 24%)

TaylorMade M2 Drivers 2017  + Shaft and Grip

TaylorMade M2 Drivers 2017 + Shaft and Grip

Let us Custom Build Your New M2 Driver or D Type

  The 2017 M2 driver brings golfers a new level of distance and forgiveness through all-new GeocousticTM technology. Following in the footsteps of its predecessor, the M2 driver successfully raises the bar in design and engineering through reinvented multi-material construction and advanced geometric shaping. Along with the new Geocoustic design, the M2 driver houses a new Speed Pocket that is three times more flexible than it was in the original M2. Combined, the new M2 takes the #1 selling driver to the next level of performance for all players. 

  The new lower density 9-1-1 Titanium body, 6-layer carbon composite crown and minimal sound ribs allowed for 25g of discretionary mass to be relocated low and back in the sole of the club. Together, these applications combine to increase the overall inertia of the M2 driver without sacrificing low CG, hot trajectory, or aerodynamic performance.

This year, M2 driver also comes in a D-Type variant, which features a draw-biased design to help golfers eliminate a right miss and gain more distance with a straighter ball flight. The D-Type driver (“D” representing draw) combines multiple draw-biasing design technologies to deliver an average of 12 yards—and up to 20 yards—of built-in draw-bias to help players who consistently fight fade-to-slice trajectories find more fairways. In addition to the multi-material construction, a Geocoustic sole, and an active Speed Pocket, the D-Type is more heel-weighted, has slight offset, and uses advanced visual cues to promote a square face at address and a more draw-biased face at impact.

 On Your order... list shaft and grip and we will call you with Quote also ask for our specials on custom shafts 20% OFF .

List your custom shaft and grip

HEAD LOFT LH LIE VOLUME    
M2 DRIVER 9.5° YES 56° - 60° 460CC    
M2 DRIVER 10.5° YES 56° - 60° 460CC    
M2 DRIVER 12° NO 56° - 60° 460CC    
HEAD LOFT LH LIE VOLUME    
M2 D-TYPE DRIVER 9.5° YES 57° - 61° 460CC    
M2 D-TYPE DRIVER 10.5° YES 57° - 61° 460CC    
M2 D-TYPE DRIVER 12.0° NO 57° - 61° 460CC    

Also use this link for Custom Head Weights

https://www.billybobsgolf.com/product.php?productid=18311&cat=0&page=&featured=Y

M2 Driver 2017

$330.00 (save 17%)

Callaway GBB Epic Sub-Zero Driver

FREE SHIPPING

FREE SHIPPING

Callaway GBB Epic Sub-Zero Driver

 Epic Sub-Zero Driver

  Epic Distance and Forgiveness in Our Lowest Spinning Driver. The GBB Epic Sub Zero Driver is a true paradigm shift: a powerful, low-spinning Tour-level driver that’s also incredibly forgiving -- an unheard of combination. Its high speed / low-spin characteristics make it particularly appealing to Tour pros, yet it’s so exceptionally forgiving and easy to launch that a wide range of players will want to play Epic Sub Zero.

Golf Digest 2017 Hot List Gold Medal Winner!

 These are New ($380.00) + Shaft and Grip

On Your order... list shaft and grip and we will call you with Quote also ask for our specials on custom shafts 20% OFF .

  Loft Availability   Lie CC Swing Weight
Adjustable (8°-11°) RH / LH   56.50° (Adjustable) 460 D4
10.5° Adjustable (9.5°-12.5°) RH Only   56.50° (Adjustable) 460 D4

List your custom shaft and grip

Also use this link for Custom Head Weights   https://www.billybobsgolf.com/product.php?productid=18156&cat=407&page=1

 

GBB Epic Sub-Zero Driver

$380.00 (save 16%)

Callaway GBB Epic Driver Slider

FREE SHIPPING

FREE SHIPPING

Callaway GBB Epic Driver Slider

  GBB Epic Wt. Driver

  The GBB Epic Driver represents an epic shift in how the head and face behave to enhance power, spearheaded by the innovative Jailbreak Technology and Exo-Cage/triaxial carbon construction. Any golfer, from scratch players to high handicappers, should find more speed, distance and control with GBB Epic.

Golf Digest 2017 Hot List Gold Medal Winner!

  Loft Availability Standard Length Lie CC Swing Weight
Adjustable (8°-11°) RH / LH 45.50" 58.00° (Adjustable) 460 D3
10.5° Adjustable (9.5°-12.5°) RH / LH 45.50" 58.00° (Adjustable) 460 D3
13.5° HT Adjustable (12.5°-15.5°) RH / LH Custom Only 45.50" 58.00° (Adjustable) 460 D3

 

GBB Epic Driver

Call for Price (800) 568-3868

TaylorMade R15, M1, M2 Factory Replacement Sleeve

TaylorMade R15, M1, M2 Factory Replacement Sleeve

    TarylorMade  R15, M1, NEW M2 Factory Replacement Sleeve This is the New Sleeve from TaylorMade, it fits the New R15 Drivers and Woods it will adjust to + or 2º Degree for total of  4º Degrees of adjustment. this Sleeve will fit the Earlier Models  R1, RBZ Stage 2, Jet Speed, SLDR .

Available in .335 RH

R15 & M1, M2 Factory Sleeve

$28.00 (save 12%)

TaylorMade New 2017 M1, M2 Factory Replacement Ferrule

TaylorMade New 2017 M1, M2 Factory Replacement Ferrule

    TaylorMade NEW 2017 M1, M2 Factory Replacement Ferrule. It fits the New (2017) M1, M2  Drivers and Woods.

Available in  RH and LH  configurations

2017 M1,M2, FERRULE

$1.00 HALF PRICE!

CMX® Cobra Universal Adaptor fits all  F7, 7+, King LTD, F6, 6+, Fly Z, Z+, Bio Cell

CMX® Cobra Universal Adaptor fits all F7, 7+, King LTD, F6, 6+, Fly Z, Z+, Bio Cell

 

Billy Bob's CMX® Aftermarket Universal Cobra adaptor allows for 8 different loft and or face angle adjustments for the Cobra F7, F7+, King LTD, F6, F6+, Fly Z, Fly Z+, Bio Cell and Bio Cell Pro drivers.

Because the Universal Adaptor simply list +/- loft and face angle settings it can be used in any of the above mentioned models without having to stock multiple adaptors for Pro and Standard Drivers, Fairways and Hybrids.

Features:

  • Right Hand (Can be used in left hand heads - Numbers will be reversed)
  • Available in .335" for drivers and fairways or .370" for hybrids
  • 8 loft and face angle settings 1/2" Degree increments.
  • Milled aluminum
  • Made in USA

COBRA CMX Uni Adaptor

$26.99 (save 16%)

EVNROLL PUTTERS

FREE SHIPPING

FREE SHIPPING

EVNROLL PUTTERS

  I have been involved in the golf business for 25 years  and have seen many products come and go..  and anybody will tell you the most important club in you're bag is the putter, you can buy that $500.00 Driver and belt it 30 to 40 yards longer straight down the fairway ...if you can, when the most important golf shot is the 4 to 6 ft putt on the green,  it's the same as those long yard hits in the fairways.  "This is the putter that I have in my Bag

    Hats off to Guerin and the People at  EVNROLL... a putter that eliminates miss-hits by broadening the sweet spot to create “The Sweetest Face in Golf.”

    Look Out Scotty!!

  Evnroll was founded by Guerin Rife and Stephen Riley at the PGA show in 2015. Guerin was in the early stages of testing and developing a technology that has the potential to revolutionize the game of golf…. a putter that eliminates miss-hits by broadening the sweet spot to create “The Sweetest Face in Golf.” The partnership combines 50 years of experience in all aspects of the golf industry, from marketing and tour representation to design, manufacture and distribution. Guerin Rife, Company CEO and chief designer, has been creating putters for 25 years starting with the very first cavity mallet. Best known for creating the famous Two Bar putter, he has designed over 40 models that have been used to win over 100 tournaments worldwide on all professional tours. He is also the inventor of face groove technology and founded the original Rife Putter Company in 2000. Stephen Riley, Company President and Director of Operations qualified as a PGA professional in 1998 and established a hugely successful golf accessories distribution company throughout Europe and the USA. He has built up extensive manufacturing facilities in both the Far East and the USA specializing in injection molding, stitching, embroidery, QC and worldwide distribution. The common bond between the two is the desire to create something special, combining Guerin’s design and innovation with Stephen’s business acumen.

 WE At Billy Bob's will custom make your putter to fit your special needs; shaft length, Loft and Lie. Comes with a Standard Winn X Pro 1.18 Grip or un cut with no grip at all.

Available in Right Hand Only

EVNROLL ER 1 Blade

$329.00

PXG® 3 Degree Factory Adjustable Sleeve

PXG® 3 Degree Factory Adjustable Sleeve

  A Factory  PXG®’s adjustable Sleeve can change the loft (+/-) 1½ degrees a total 3 degrees.

 Available in .335  3 Degree Total

PXG 3 Degree Factory

$25.00 (save 29%)

PXG® Factory Iron Ferrules

PXG® Factory Iron Ferrules

 The ferrule for the PXG Irons has a special Deep Collar and a outside diameter that only fits the Factory Irons perfectly.

  Available in .370 Parallel Tip   and a  .355 Taper Tip w/ Cup

Please Note*  The .355 Ferrule comes with a special tip cup spacer for their Iron Hosels.

These are included with ferrule.

Also please remove any debris in the hosel, it will impede the insertion on the bottom spacer cup if not cleaned.

 

PXG Iron Ferrules .355

$1.50

PXG® 3 & 4 Degree Aftermarket Adjustable Sleeve (CMX®)

PXG® 3 & 4 Degree Aftermarket Adjustable Sleeve (CMX®)

  Our CMX® Aftermarket version of the PXG®’s adjustable hosel can change the loft (+/-) 1½ degrees a total 3 degrees which is the factory setting, but we also make the sleeve for those who want more adjustment, this can change the loft (+/-) 2 degrees for a  4 degree total adjustment.

Available in .335 and either 3.0 or 4.0 Degree  R-H

L-H is available upon special request

PXG CMX 3 & 4 Degree

$20.00 (save 33%)

Krank Golf® Formula 6.5 Adjustable Sleeve

Krank Golf® Formula 6.5 Adjustable Sleeve

Krank Golf®

This is the Factory Sleeve that fits the Krank 6.5 Driver 

Adjustment are + - 1 Degree with a total of 2 Degrees of adjustment

Krank Driver 6.5 Adj Sleeve

$25.00 (save 17%)

CMX® HOSEL BORING & REAMING VISE

CMX® HOSEL BORING & REAMING VISE

CMX® HOSEL BORING & REAMING VISE

  We hand make these here at Billy Bob's, this will hold hosels for boring and reaming on a drill press or bench. We made them with aluminum hard coated jaws.  So the aluminum won't crush down and won't mare the hosels, we also incorporated a adjustment system that is very easy to conform the hosels diameters with a simple allen wrench, works well.

  We also made it with a stronger clamping handle. This Boring & Reaming Vise is a Monster.

HOSEL BORING VISE

$79.00 (save 11%)

Scotty Cameron Weight Socket Wrench

Scotty Cameron Weight Socket Wrench

Scotty Cameron Putter Weight Hand Removal Wrench

  This Socket wrench can be used to remove the factory sealed head weights, they have special adhesive that locks in the weights, they can be pesky when first removed. You can use a 3/8 scocket wrench to release it for the first time.  You then can use the handy hand wrench to easy remove or change out weights, its small and can fit easily in you golf bag. We also include 2 extra o-ring washers.

Avail:

  • Blue
  • Red
  • Black

 

SCOTTY WRENCH H RED

$19.95

Universal Graphite Shaft Extension

Universal Graphite Shaft Extension

Universal Graphite Shaft Extensions

  We at Billy Bob's have had many requests to come up with a Universal Graphite Extension, one that will work with both standard and oversize butt diameters as well as fill up those larger butt diameters that our oversize extension won't do.  We designed it based on the same engineering principals that we have used in our existing graphite extension line.

  • Regular Extension ( .600 O.D on the Handle .480 O.D on the Insertion Tip)
  • Oversize Extension  (.600 O.D on the Handle .535 O.D  on the Insertion Tip)
  • Universal Extension (.600 O.D on the Handle  .560 O.D on the Insertion Tip at Full Expansion)

Click on this link for instructions on the Universal

Universal Extension

$2.04 (save 18%)

CMX® Shaft Clamping System ( Vise or Bench Mount ) 5-1/2 " Jaws

CMX® Shaft Clamping System ( Vise or Bench Mount ) 5-1/2 " Jaws

  This is the New Billy Bob Shaft Clamping System by CMX®.  Just like our Shaft Extractor, our Shaft Clamping System is machined from Billet Aircraft Aluminum.  This will make your repair and gripping tasks as easy as possible, our Shaft Clamping System has a positive Clean Ratchet Mechanism and the Clamping Jaws are 5 1/2" of solid gripping power (same as our Shaft Extractor) this will save shafts from cracking or breaking, more holding power with less pressure.

 The Clamping System can be easily Mounted on a Vise over your Gripping Station or Mounted on a bench,  it also can be adapted to a Mitchell Gripping Station.  Remove the 4 bolts that hold there clamp,  remove it and bolt on ours.

 The quality of this tool is so Good that we Guarantee it for as long as you own it*. 

*(Except for the Jaws...if they wear - we have replacements if needed)

CMX Shaft Clamping System

$120.00

TaylorMade R15 Headweights

TaylorMade R15 Headweights

We make these Aftermarket Replacement Weights for the NEW TaylorMade  R15 Drivers.

This System would fit the New TaylorMade R15 Drivers  only

The weights provided are; 6, 8, 15  Grams  includes the top weight and the bottom weight and the screw.

 

Get Instructions for Weights Removal here

 

 

R15 WTS. 6g

$18.99

R15, RSi, Aero Burner, Speed Blade, RBZ, Rocketbladez Iron Ferrules

R15, RSi, Aero Burner, Speed Blade, RBZ, Rocketbladez Iron Ferrules

    TarylorMade New R15, RSi, Aero Burner, Speed Blade, RBZ, Rocketbladez Iron Ferrules

  • This is the aftermarket ferrule that we are making that will fit the NEW TaylorMade Irons, it has a special collar and one silver ring that matches the hosel diameter perfectly,  you will not have to turn down this ferrule, it will give you that factory finish.

Available in .360  Taper Tip  .370 Parallel Tip

 

R15 IRON FERRULE

$1.00

TaylorMade Factory Replacement Headweights M1 2016 Driver (Only)

TaylorMade Factory Replacement Headweights M1 2016 Driver (Only)

TaylorMade Factory Replacement Head Weights M1 Driver Head

There are 2 different color Head weights.... Red one is for the High & Low Launch.....Black one is for  Face Fade and Draw. The top caps and screws are all the same weight, it's the bottom weights that are different grams.  We have them in  5, 7, 9, 11, 13 Grams. The 11 and 13 are made from Tungsten and are a little more expensive.

Please Note*  We sell the Cap, Screw, Bottom Weight as set all together... all 3 parts are equal to the total weight described above.

 

 

Headweights blk 5gr

$18.99 (save 24%)

CMX® Aftermarket Sleeve Fits R15, R1 & M1, M2 2016,2017

CMX® Aftermarket Sleeve Fits R15, R1 & M1, M2 2016,2017

    TarylorMade R15, R1 & M1, M2  CMX® Aftermarket Replacement Sleeve

  • This is the New Sleeve from CMX®, it fits the New M1, M2 2016,2017, R15, R1 Drivers and Woods .370 Rescue it will adjust to + or 2º Degree for total of  4º Degrees of adjustment. this Sleeve will fit the Earlier Models  R1, RBZ Stage 2, Jet Speed, SLDR. 

Available in .335 . 350, .370 Rescue  RH, LH

 

R15,R1,M1,M2 CMX Sleeve

$20.00 (save 29%)

New Ping G Series Ferrules

New Ping G Series Ferrules

  The New Ping G Series Drivers and Fairway Clubs introduced this year have a unique size Ferrule and Collar counter sink. The ferrules are made from Different Materials, it is softer and more pliable.   Older ferrules will not fit as good as these. So if you want to have that club with a factory finish and look you need... use these. Also you don't have to turn them down and polish them (Time Saver).

We at Billy Bob’s Golf have come up with the proper replacement Ferrule  … that is what we do.. ENJOY!!!

These Ferrules will fit New G Series Drivers and Woods .335 Tip only

 

PING G Series Ferrules

$1.50 (save 40%)

TaylorMade SLDR, R15, M1, M2 (2016) Factory Replacement Ferrule

TaylorMade SLDR, R15, M1, M2 (2016) Factory Replacement Ferrule

    TarylorMade  R15, M1, M2 (2016) Factory Replacement Ferrule. It fits the R15, New M1, M2 and the SLDR Drivers and Woods.

Available in  RH and LH  configurations

SLDRFERRH BB#9090RH

$4.00 (save 33%)

 Ping G Series Factory Replacement Adjustable Sleeve

Ping G Series Factory Replacement Adjustable Sleeve

Factory Replacement Adjustable Sleeve Fits the New Ping G Series Driver and Woods  RH  .335   2 Degree  Adjust

1o Plus or Minus +-  Ping change the style and look for the new G Series Adaptor Sleeve and added a Softer Poly Ferrule with a deep contersink

avail: .335  R-H only

G SERIES PING

$29.00 (save 17%)

TaylorMade M2 (2016) Head Weights

TaylorMade M2 (2016) Head Weights

TaylorMade Replacement Head Weights M2 Driver Head

  We here at Billy Bobs Have had many request for replacement Weights for the  New TaylorMade M2 Drivers. The weight is used in the sole of the club to adjust the swingweight due to shaft changes (shaft weights and shaft lengths), and also simple swingweight adjustments.  The weight has a very special tip and we supply the wrench tip so it can be removed.

  Note* Taylor says that the weight is not removable. It can be removed with a special bit that we provide and it's included. Also they use a lock tight on the treads which can easily remove by applying a little heat to the weight screw.

They are available in 5 different gram weights: 4, 6, 8, 10, 12

See Image tag for picture of the special bit

M2 WEIGHTS 4g

$18.99 (save 24%)

Billy Bob's CMX® G30 Adaptor Fits The Ping G30 Driver & Woods

Billy Bob's CMX® G30 Adaptor Fits The Ping G30 Driver & Woods

  The New Ping G30 Driver and Fairway Woods are now on the market, we at Billy Bob’s have come up with a CMX® G-30 Aftermarket Sleeve that will fit the G-30 Drivers and Woods.
   We made them different than the OEM, they are a bit Longer in Length with more shaft insertion, and with 2 Different Adjustments: Plus or Minus 1 Degree Adjustment (standard) and a Plus or Minus 1.5 Degree Adjustment.... they are available in .335 and .350 R-H and L-H Versions. So now you have same as the OEM  or a bit more adjustement than the OEM.

Ping is a Register Trademark

G30 CMX ADP

$25.00

 Ping G30 Factory Replacement Adjustable Sleeve

Ping G30 Factory Replacement Adjustable Sleeve

Replacement Adjustable Sleeve Fits the Ping G30 Driver and Woods  RH  .335   2 Degree  Adjust

1o Plus or Minus +-

G30 PING

$29.00 (save 17%)

Mizuno JPX 850, 900 Adjustable Sleeve Adaptor Driver, Fairway, Hybrid

Mizuno JPX 850, 900 Adjustable Sleeve Adaptor Driver, Fairway, Hybrid

   Mizuno introduced a sliding weight system called Fast Track to alter a driver's draw/fade tendency. Mizuno has now evolved this break through technology to also be able to customize spin rate and launch angle in the JPX-900 Driver, JPX-850 Driver, Fairway, Hybrid helping all swing speeds achieve maximum possible total yardage.

"The genius of the new Fast Track is that it adds the dimension of launch angle and spin rate. Now the player is truly in control of maximizing all aspects of their ball flight off the tee."

Available .335 includes screw and washer will fit Driver

Note* Fairway is different and so is the Hybrid.

.335 Fairway Shorter Length

.370 Hybrid  Larger I.D

MIZ JPX 850, 900

$20.00 (save 20%)

 Ping Aftermarket Head Weights  New G Series & G30

Ping Aftermarket Head Weights New G Series & G30

   We At Billy Bob’s had  many request to come up with an Aftermarket Replacement Weight System that would fit the Ping G30 & New G Series Drivers and Fairways

 The weights provided are; 8, 10, 12, 14, 16, 20 (Tungsten) Gram increments EACH SOLD SEPARATELY

Please Note*  Screw provided is appox 1 1/2 gram, or you can use the one that comes with your Club Head there may be small difference in weight +- 1/2 Gram

PING G30WTS.8

$13.99 (save 22%)

CMX® Vertical or Horizontal Specialty Shaft Extractor Base with Jack

CMX® Vertical or Horizontal Specialty Shaft Extractor Base with Jack

CMX® VERTICAL OR HORIZONTAL SPECIALTY CLUB HEAD SHAFT EXTRACTOR BASE AND JACK

This will be the last Shaft puller You will ever Need !!

This space saving Vertical or Horizontal Shaft Extractor will meet all your club-head pulling needs!
It will pull all the specialty clubs including: CALLAWAY, PING, TITLEIST,
WILSON FAT SHAFTS, TAYLORMADE, CLEVELAND, and All Others including the New Composite Heads without any special adaptors!
I decided to tackle a problem I had with every shaft extractor I've ever owned. No matter what type of shaft clamping unit they contained, only a small fraction of the clamp contacted the actual shaft. To correct the many problems this caused, such as over torque and crushing shafts, I developed a revolutionary clamping system, (Patent Pending) that tapers with the contour of the shaft, completely gripping a 5 ½" length of shaft, you now don't have to clamp down so hard and crack those graphite shafts.   Caution* on light weight graphite shafts such as 40 or 50 grams to much jaw pressure can damage the shaft, buy adding a little more heat and patience will remove the head easly. Be sue to do the same heating on those shafts such as the Titleist and Callaway's.
So please use enough heat to release the epoxy bond. 

 I have also designed the gripping station to float and move with the holding wheel of the shaft extractor, this allows the pressure on the shaft and club head to position itself evenly, allowing the puller to remove the head squarely.
Not only is it simple to use, all that's required is a ¾" socket and ratchet, or a ratchet wrench.

This Puller is excellent for the high volume repair shops.

I realize the price tag on this workhorse is a bit high but worth every cent. We could make it cheaper having it machined overseas, make it with cheaper materials not aircraft quality materials, but that's not our style, all the parts are machined and Made here in the USA.  I am so confident that my Vertical Shaft Extractor is the easiest and best shaft extractor you have ever used.

I offer rubber Gripping Jaws and Teflon Bushing, both can wear with heavy use (replacements are available).

 

SHAFT EXTRACTOR BASE

$389.00

Scotty Cameron Putter Weights (1 Pair)

Scotty Cameron Putter Weights (1 Pair)

Scotty Cameron Putter Weights Fit the Following Putters;

Select             All Weights Sold Per Pair    

Colors available:  RED,  BLUE,  BLACK, 10g, 15g, 20g, 25g, 35g, 40g  and CLEAR POLISH...   Polish works out great if you want to paint a custom color yourself and their less expensive 10g,15g,20g available

  • Newport
  • Newport 2
  • Newport 2.5
  • Fast Back
  • Square Back

Futura

  • Futura X
  • Futura X Dual

Golo

  • Golo 3
  • Golo 5
  • Golo S 5
  • Golo 7
  • Golo 7 Dual Balance

Square Back

  • Square Back Limited
  • My Girl
  • Golo N 7
  • Golo N 5

 

 

SCOTTY WTS10R

$35.00 (save 46%)

Nike New Vapor Fly, Vapor,  VR-S Covert & 2.0 Adjustable Sleeve (Drivers Only)

Nike New Vapor Fly, Vapor, VR-S Covert & 2.0 Adjustable Sleeve (Drivers Only)

Nike's   New Vapor Fly, Vapor, VR-S Covert  and 2.0 Flex Loft ...Factory Replacement Sleeve,  It is adjustable from 8o to 12o degrees  with 3 different face angles.

Combination Sleeve Fits both R-H and L-H .335 tip.


 

NIKE COVERT VAPOR SLEEVE

$35.00 (save 22%)

Nike Vapor, VR-S Covert 2.0 Tour Fairway Adjustable Sleeve  3 Wood & 5 Wood

Nike Vapor, VR-S Covert 2.0 Tour Fairway Adjustable Sleeve 3 Wood & 5 Wood

Nike's  Vapor, VR-S 2.0 Covert Fairway  3 & 5 Woods ...Authentic Original Factory Replacement Sleeve,  It is adjustable from 13o to 17o degrees

and the 5 Wood 17o to 21o  with 3 face angles, closed, neutral, and open

Sleeve Fits R-H .335 tip.


 

NIKE COVERT FAIRWAY SLEEVE 12-17

$35.00 (save 22%)

Brass Swingweights Steel Shafts

Brass Swingweights Steel Shafts

  We at Billy Bob’s had many request for precise brass swing weight for .335, .355 and .370 tips for Steel Shafts. These are the same as the OEM use in there irons and woods and can be reused if needed. Special Note*  Very few club builders put steel shafts in .335 drivers but if this is what you want to do, please epoxy the weight in the club then sand and abrade the shaft tip.

Available Weights in:  2, 4, 6, 8, 10 Grams 

335 355 2g

$1.50

Nike VRS Covert Ferrule

Nike VRS Covert Ferrule

Nike's  has come out with a New Club the VRS Covert...It has Adjustable Sleeve, and comes with a very wide short Shank Ferrule,  it would be hard to fine a ferrule that will fit this sleeve.  So we came up with the replacement.  That what we do!!! .335 shaft tip  and will fit the factory sleeve quit nicely.


 

NIKE-COVERT

$1.00

Special 1" Wedge Ferrule For Taper Tip Irons .365 ID - .575 OD

Special 1" Wedge Ferrule For Taper Tip Irons .365 ID - .575 OD

     We have had many request for a Ferrule that is 1” long and will fit the Newer Wedges on the market today,  they have a OD .575 and ID of .365, they will fit all the taper tip shafts including the KBS wedge shaft which has a bit larger OD due to the paint finish, and if you what install a .370 shaft they can be ream to .370 easily. So now you have a ferrule that will fit those large hosels wedges and retain that same factory look.

NCF3651-TP

$0.27

 CMX® RBZ Stage 2 fits SLDR & JetSpeed  335, 350, 370 Rescue

CMX® RBZ Stage 2 fits SLDR & JetSpeed 335, 350, 370 Rescue

    The New R1 and RBZ Stage 2 Drivers and Woods have been real popular and of course  TaylorMade change the Sleeve configuration. They will not Fit the older Style R11,R9 RBZ Drivers and Woods. RBZ Stage 2 Sleeve is full 3 Degree adjustment,  +1.5 o  Higher Loft  to -1.5 Lower Loft and with 12 settings open and closing and lie adjustments, This can give you many different settings.

  We at Billy Bob’s developed our CMX® line of adjustable adaptors a little different. We made the sleeve a little taller and there is No Ferrule needed, which makes Removing and Replacing shafts easier.  The same is with the RBZ Stage 2 No Ferrule.  We made them to have a 1 1/2 inch shaft insertion.  All adjustment setting are marked clearly on the sleeve. Also they are interchangeable with both the R1 and Stage 2 heads and the New SLDR, and the New TaylorMade JetSpeed, and the New Adams XTD Ti.  They are all interchangeable.... so if you want your Stage 2  3 degree,  it can be change to 4 degree just use the R1 sleeve.

They are available in R-H and L-H.  .335 and .350 .370 Rescue

RBZSTAGE2CMX335RH

$20.00 (save 33%)

CMX® Force Fit Adjustable Sleeve Callaway Big Bertha, Alpha Drivers, 815, Mini Driver

CMX® Force Fit Adjustable Sleeve Callaway Big Bertha, Alpha Drivers, 815, Mini Driver

 We at Billy Bob’s Developed an Aftermarket Adjustable Sleeve CMX® Force Fit with Doulbe Cog Collar....  it Fits the Callaway Opti Force, New X2-Hot, and New Great Big Bertha and the BB Alpha,  Mini Driver all are with Standard Factory Adjustments.

Avail: .335 and .350 R-H L-H

Callaway Golf   is a Registered Trademark         

 

CMX FORCE-FIT335RH

$31.99 (save 16%)

Callaway Razr-Fit, Opti Fit, Opti Force, X2-Hot, New XR Series, Big Bertha Ferrule

Callaway Razr-Fit, Opti Fit, Opti Force, X2-Hot, New XR Series, Big Bertha Ferrule

Here at Billy Bob's we make this Ferrule that will fit the New XR Series Woods, Razr-Fit , Opti Fit and the Opti Force, X-Hot and the X2-Hot, Big Bertha and the Alpha

These ferrules will also fit the Callaway CMX Aftermarket Adaptor Sleeves

Ferrule in sizes .335 and .350.

RAZOR FIT FER335

$2.00 (save 43%)

Callaway Plastic Ball End Cap fits all the Adjustable Sleeves

Callaway Plastic Ball End Cap fits all the Adjustable Sleeves

   This is the replacement ball end cap that will fit most Callaway Adjustable Sleeves. The older version Adjustable Sleeves such as the Razr Fit, Opti Fit  and the Tour Fit sleeves were made with a hard plastic which fractured or cracked, we've had requests to have a Replacement for these and you should have a few in your shop if needed.  We make them out of a softer and more pliable ABS.

  If you would like to use our Billy Bob CMX® Adjustable Collars such as the Razr fit 2 degree Collar (OEM standard is only 1 degree)  or the use the Billy Bob Opti-fit Tour Double Cog Collar on you Razr-fit, now changing it to a Opti-Fit Tour Sleeve....You can now do so without the fear of cracking the plastic Ball End Cap.

CALLAWAY BALL END CAP

$3.00

CMX® R-Fit Sleeve Fits Callaway Razr Fit, Opti Fit, X Hot Extreme

CMX® R-Fit Sleeve Fits Callaway Razr Fit, Opti Fit, X Hot Extreme

THE BILLY BOB’s CMX Aftermarket Replacement Adjustable Sleeve that Fit the Callaway Razr Fit, Opti Fit & Extreme, X Hot with 2 Removable Collars 1 Degree or 2 Degree

Available .335 or .350 shaft tips

RAZOR-FIT 1o 335

$30.00 (save 14%)

Callaway 2015-2016  Head Weights Big Bertha and Alpha

Callaway 2015-2016 Head Weights Big Bertha and Alpha

Individual head weights for the Callaway Opti Force, Big Bertha the X2 Hot and the Alpha Heads.

   Please Note*  The X2 Hot Pro has a different size weight and these will not fit these heads also the Great Big Bertha (see the Callaway 2016 Weights).  We will be coming out with this weight for the x2 hot pro

Aavaiable in 3,4,5,7,9,11,13,15 gram increments (All Weights sold separately)

BB Weights 3

$9.50 (save 27%)

Weights for the Callaway RAZR-Fit and Tour Authentic RAZR-Fit Opti-Fit

Weights for the Callaway RAZR-Fit and Tour Authentic RAZR-Fit Opti-Fit

Individual weights for the Callaway RAZR-Fit Driver and Tour Authentic RAZR-Fit Driver. The weights are available in seven Opti-Fit Tour Weight options (3, 5, 7, 9, 11, 13, and 15 grams) that allow golfers to shift the clubhead’s center of gravity to more finely tune ball flight and trajectory. Avail in Razr-Fit Red and Opti-Fit White (All Weights sold separately)

 

RAZRWEIGHT3W

$8.00 (save 20%)

Callaway .355 Taper Tip Iron Ferrule

Callaway .355 Taper Tip Iron Ferrule

We have had many request for the Callaway Taper Tip .335 Iron ferrules which changed from the o-ring in late 2010 to present, it's now a 3/4 inch Tall Black Ferrule with a large counter-bore, (see Photo) this will fit a .355 Taper Tip Hosel and will fit these Callaway Heads: X Prototype iron, RAZR X Muscleback iron, RAZR X Tour iron, X Forged iron, X Series JAWS Wedges, X Series JAWS CC Wedges, RAZR X Forged Wedges, CC Forged Wedges

Callaway .355 Iron Ferrule

$1.00

Callaway .370 Iron Ferrule

Callaway .370 Iron Ferrule

We have had many request for the Callaway Iron ferrules which changed from the o-ring in late 2010 to present, it's now a 3/4 inch Tall Black Ferrule with a large counter-bore, (see Photo) this will fit a .370 hosel and will fit these Callaway Heads: X HOT iron, X HOT PRO iron, RAZR XL iron, RAZR X iron, X-24 HOT iron, Diablo Forged iron, Diablo Edge iron, X Utility Prototype

Callaway .370 Iron Ferrule

$1.00

Callaway I-MIX Metal Sleeve Adaptor Kit

Callaway I-MIX Metal Sleeve Adaptor Kit

  Callaway Golf has the I-MIX Series line and has sold many of these heads and many are now available without the Metal Sleeve. You may have people coming into you shop wanting you to install a shaft or they have the head without the sleeve and wench.... it is a potential shaft sale walking out the door or.... let alone impossible to re-shaft without a sleeve.

We at Billy Bob's have developed a Metal sleeve hosel that can be permanently installed in the head which will allow you to use all of our Callaway Ferrules & Adaptors plus the popular Clock Ferrule which allows you to adjust the loft and lie of the club. A Simple fix for a complex problem.

The I-MIX Kit fits the FT-IQ Driver and the FT9 Driver

(instructions included)  view the PDF



See the Installation Instructions here:
i-Mix Adapter Installation Instructions HERE

IMIXKIT

$25.00

TaylorMade R1 Factory TP.335 Sleeve

TaylorMade R1 Factory TP.335 Sleeve

TaylorMade R1 Factory Sleeve,TP .335 with 2 degree adjust (4 degrees total).  Fits new R1 and RBZ Stage 2 drivers and fairway woods. ( NOTE: while this sleeve will fit the RBZ Stage 2 driver, the factory RBZ Stage 2 driver is only a 1.5 degree adjust.  This sleeve will give an additional 1 degree of adjustment over the standard factory sleeve when installed in the RBZ Stage 2 clubhead).

R1 Factory Sleeve TP.335

$28.00 (save 7%)

TaylorMade R1 Factory .350 Sleeve

TaylorMade R1 Factory .350 Sleeve

    TaylorMade R1 Factory Sleeve, .350 with 2 degree adjust (4 degrees total).  Fits new R1 and RBZ Stage 2 drivers and fairway woods. ( NOTE: while this sleeve will fit the RBZ Stage 2 driver, the factory RBZ Stage 2 driver is only a 1.5 degree adjust.  This sleeve will give an additional 1 degree of adjustment over the standard factory sleeve when installed in the RBZ Stage 2 clubhead).

R1 Factory Sleeve.350RH

$28.00 (save 7%)

CMX® TaylorMade R1 Aftermarket Sleeve

CMX® TaylorMade R1 Aftermarket Sleeve

   The New R1 and RBZ Stage 2 Drivers and Woods have been real popular and of course  TaylorMade change the Sleeve configuration. They will not Fit the older Style R11,R9 RBZ Drivers and Woods. R1 Sleeve is full 4 Degree adjustment,  Loft can be adjusted from 8 Degrees to 12 Degrees and with 12 settings open and closing and lie adjustments, This can give you many different settings.

  We at Billy Bob’s developed our CMX line of adjustable adaptors a little different. We made the sleeve a little taller and there is No Ferrule needed,  which makes Removing and Replacing shafts easier.  The same is with the RBZ Stage 2 No Ferrule.  We made it so there is a 1 1/2 inch shaft insertion.  All adjustment setting are marked clearly on the sleeve. Also they are interchangeable with both the R1 and Stage 2 and the New SLDR heads,  so if you want your Stage 2, or SLDR  3 degree,  it can be change to 4 degree just use the R1 sleeve.

They are available in R-H and L-H.  .335 and .350 .370 Rescue

R1CMX335RH

$20.00 (save 33%)

TaylorMade R1 Factory Replacement Ferrule

TaylorMade R1 Factory Replacement Ferrule

TaylorMade R1 Factory Replacement Ferrule

Avaiable: Right Hand and Left Hand

R1FerrRH

$4.00 (save 43%)

RBZ Stage 2 Factory Sleeve 1.5 Degree Adjustable

RBZ Stage 2 Factory Sleeve 1.5 Degree Adjustable

    TaylorMade  RBZ Stage 2  Factory Sleeve for Drivers and Fairway woods, available in R-H and L-H available in .335 and .350, .370 Rescue shaft tips with 1.5 degree adjust.

 

RBZSTAGE2-FRH335

$28.00

SLDR 1.5 Factory Replacement Sleeve

SLDR 1.5 Factory Replacement Sleeve

   The SLDR 1.5   Factory Replecement Sleeve this sleeve will adjust up to 3 Degrees , this sleeve will fit the R1, RBZ Stage 2, the Jet Speed and the Adams XTD TI

  They are available in R-H   .335 only

 

SLDR FACTORY ADAPTOR

$28.00 (save 12%)

 CMX®Tayormade Jetspeed Aftermarket Sleeve also fits SLDR

CMX®Tayormade Jetspeed Aftermarket Sleeve also fits SLDR

    The New JetSpeed Drivers and Woods have full 3 Degree adjustment,  +1.5 o  Higher Loft  to -1.5 Lower Loft and with 12 settings open and closing and lie adjustments, This can give you many different settings.

  We at Billy Bob’s developed our CMX® line of adjustable adaptors a little different. We made the sleeve a little taller and there is No Ferrule needed, which makes Removing and Replacing shafts easier.   We made them to have a 1 1/2 inch shaft insertion.  All adjustment setting are marked clearly on the sleeve. Also they are interchangeable with both the R1 and Stage 2 heads and the New SLDR, and the New TaylorMade JetSpeed, and the New Adams XTD Ti.  They are all interchangeable.... so if you want your Stage 2  3 degree,  it can be change to 4 degree just use the R1 sleeve.

They are available in R-H and L-H.  .335 and .350

CMX JetSpeed335RH

$20.00 (save 33%)

CMX®Aftermarket Metal Sleeves FITS RBZ, R11s, R11, R9

CMX®Aftermarket Metal Sleeves FITS RBZ, R11s, R11, R9

This is the Billy Bob's CMX Replacement Metal Sleeve Adaptor, they fit all the TaylorMade RBZ, R11s, R11, R9's heads. We make this out of 7075 Aircraft Aluminum  with very close tolerances and it's Made Here in USA. These will fit either .335, .350 or .370 shaft tip. with options of 1º 2º 3º degree full adjustments, these will give you more adjustment than the OEM Original Part.

You can add 4 Different Colored Ferrules they will all fit the Original OEM Sleeve and the Billy Bob's Metal Sleeves

TaylorMade is a registered trademark

2R11335TP-A1-BLKW

$19.95 (save 33%)

TaylorMade R11s Factory Sleeve 3 Degree Offset

TaylorMade R11s Factory Sleeve 3 Degree Offset

TaylorMade R11s Factory Sleeve 3 Degree Offset (Red)

 these will fit a R11s TP  shaft tip.  The Metal Sleeve will make a degree adjustment this will give you a 1.5º either way for total of .

Avail: .335 and .350   R-H  or L-H

R11sTP335RH

$23.00 (save 23%)

TaylorMade Ferrules RBZ, R11, R9  All colors incl. Ghost Ferrule™

TaylorMade Ferrules RBZ, R11, R9 All colors incl. Ghost Ferrule™

TaylorMade Ferrules RBZ, R11, R9 All colors including Ghost Ferrules™. We have Made all the Billy Bob's Ferrules that fit the Old and New Line of TaylorMade Line of Adjustable Clubs, they will fit the Factory Sleeve or our After Market sleeve also.  You now have many different choices to Look Good.

9011W

$4.50 (save 25%)

Cobra MyFly 8 Bio Cell Factory Sleeves

Cobra MyFly 8 Bio Cell Factory Sleeves

   We at Billy Bob’s have the Factory sleeve replacement that fis the Cobra Bio Cell New line of Drivers, Fairway and Hybrids; they are MyFly 8, MyFly, ZLE.

 It has a 1.5 degree offset which will give a total 3 degree from side to side, Driver; (std) 9 to 12 Loft, Fairway and Hybrid.

They will give you a 3 degree adjustment on all three heads

Available in R-H .335

 

COBRABIO335DR

$27.50 (save 21%)

CMX® Bio fits Cobra MyFly 8 Bio Cell Sleeves

CMX® Bio fits Cobra MyFly 8 Bio Cell Sleeves

  Billy Bob's CMX® Aftermarket Replacement Sleeve that fits the Cobra Bio Cell line of Drivers, Fairway and Hybrids; they fit the MyFly 8, MyFly, ZLE.

 It has a 1.5 degree offset which will give a total 3 degree from side to side, Driver; (std) 9 to 12 Loft, Fairway 13 to 16 and Hybrid 23.5 to 26.5 .

They will give you a 3 degree adjustment on all three heads

Available in R-H .335, .350  and .370

                     L-H .335, .350  and .370 

 

COBRA CMX BIO335DR

$25.00 (save 22%)

Cobra AMP Cell Factory Sleeve

Cobra AMP Cell Factory Sleeve

   We at Billy Bob’s have the Factory sleeve replacement that fit the Cobra AMP Cell New line of Drivers.

 It comes with factory ferrule black with 2 silver rings, it has a 1.5 degree offset which will give a total 3 degree from side to side 8.5 to 11.5 its set in the draw position which is the most popular.

it will fit in the Amp Cell Pro Drivers  7.5° - 10.5°, Amp Cell Drivers 8.5° - 11.5°, Amp Cell Ladies Drivers 11.5° - 14.5°  which will give you a 3 degree adjustment on all three heads

Available in R-H or L-H .335 and .350

 

COBRACELL335RH

$27.50 (save 21%)

COBRA CMX® Aftermarket Cell Fit

COBRA CMX® Aftermarket Cell Fit

   We at Billy Bob’s Developed an Aftermarket Adjustable Sleeve,  CMX®  that fits the Cobra AMP Cell New line of Drivers.

 It comes with a choice 3 colored Ferrules to match the Heads or factory ferrule black with 2 silver rings, it has a 1.5 degree offset like the factory sleeve which will give a total 3 degree from side to side 8.5 to 11.5 its set in the draw position which is the most popular. We make all our CMX® sleeves in the USA.

Available in R-H or L-H .335 and .350

 

CMX CELL FIT 335 RH

$25.00 (save 29%)

CMX® Titleist 910, 913, 915 Straight Metal Sleeve

CMX® Titleist 910, 913, 915 Straight Metal Sleeve

   We at Billy Bob's had many request for a CMX Straight Sleeve version that fits the Titleist  913, 915 (Driver Only) and the 910 D2 D3 Drivers and Fairway Woods.

With a Zero Loft and Zero Lie   Now you can have many shaft combinations within a straight fit Hosel configuration.

Also coming soon will be the 913 Fairway and Hybrid Versions

910STRAIGHT335

$18.00

Titleist 910, 913, 915 CMX® Aftermarket Replacement Metal Sleeve .335

Titleist 910, 913, 915 CMX® Aftermarket Replacement Metal Sleeve .335

Billy Bob's CMX Aftermarket Replacement Sleeve fits the Titleist 913, 915 (Driver Only)  and 910 D2 D3 Drivers and Fairway Woods Fits .335 Shaft tip

This Sleeve is uniquely  different than the OEM original, the CMX sleeve itself still has the factory offset which is the same as the OEM,  but what makes the CMX Tour Fit Adapter different is the Compound Collar can be removed and replaced with other Collars to give you a combination of approximately  48 different adjustments (any extra collars are sold separately.... sleeve comes with Factory 1/2 Collar.

Comes with complete set of instructions

 

910SLEEVE-335C12RH

$39.99 (save 20%)

Titleist 910, 913, 915 CMX® Aftermarket Replacement Metal Sleeve .350

Titleist 910, 913, 915 CMX® Aftermarket Replacement Metal Sleeve .350

Billy Bob's CMX Aftermarket Replacement Sleeve fits the Titleist 913, 915 (Driver Only) or 910 D2 D3 Drivers and Fairway Woods Fits .350 Shaft tip

This Sleeve is uniquely  different than the OEM original, the CMX sleeve itself still has the factory offset which is the same as the OEM,  but what makes the CMX Tour Fit Adapter different is the Compound Collar can be removed and replaced with other Collars to give you a combination of approximately  48 different adjustments. (any extra collars are sold separately).

Comes with complete set of instructions

   (any extra collars are sold separately).

 

910SLEEVE-33513

$39.99 (save 20%)

Titleist 910 CMX® Aftermarket Replacement Metal Sleeve .370  Hybrid

Titleist 910 CMX® Aftermarket Replacement Metal Sleeve .370 Hybrid

Billy Bob's CMX Aftermarket Replacement Sleeve fits the Titleist  910 .370 Hybrid Woods

We offer this in a Interchangeable  1/2º Compound Collar which is the Standard OEM Collar but Please Note* this sleeve and Collar will not fit into the Drivers and Woods

they will only fit in the Hybrids.

Comes with complete set of instructions

 

 

910SLEEVE-370C12

$45.00 (save 10%)

Titleist 915, 913, 910 Replacement Metal Sleeve Kit incl: 1/4, 1/2, 3/4 Collars

Titleist 915, 913, 910 Replacement Metal Sleeve Kit incl: 1/4, 1/2, 3/4 Collars

 This Sleeve is uniquely  different than the OEM original, the CMX sleeve itself still has the 2.00 degree factory offset which is the same as the OEM,  but what makes the CMX Tour Fit Adapter different is the Compound  Collar can be removed and replaced with other Collars to give you a combination of approximately  48 different adjustments. The Kit contains: one 1/4º Compound Collar, 1/2º Compound Collar, 3/4º Compound Collar. Available in .335 or .350

The kit comes in a .335..   Please let us know if you want a .350 in the order Notes.

Comes with complete set of instructions

 

910 SLEEVE-KIT

$64.95 (save 13%)

Titleist 913, 915 CMX® Fairway Sleeve .335

Titleist 913, 915 CMX® Fairway Sleeve .335

 Billy Bobs New 913, 915 CMX® Aftermarket  Fairway Adjustable Sleeve will give you all the 16 different settings like the Factory Club, Titlest change the 913 sleeve, its shorter and will not fit the old style 910 fairway, we made it's so you don't have to use a ferrule,  it's very easy to remove and replace shafts.  We make 3 different collars 1/4" degree and 1/2" Degree (Factory Standard) and 3/4" degree this will give you 48 different adjustments. (any extra collars are sold separately....sleeve comes with 1/2 degree Factory Standard).

Avail: .335

913 CMX Fairway Sleeve12

$39.99 (save 11%)

Titleist 913, 915 CMX® Hybrid Sleeve .370

Titleist 913, 915 CMX® Hybrid Sleeve .370

 Billy Bob's New 913, 915 CMX ® Aftermarket  Hybrid Adjustable Sleeve will give you all the 16 different settings like the Factory Club, Titlest change the 913 sleeve, its shorter and will not fit the old style 910 Hybrid, we made it's so you don't have to use a ferrule,  it's very easy to remove and replace shafts. .

Avail: .370 only

913 CMX Hybrid Sleeve

$39.00 (save 13%)

Adams CMX® Adjustable Sleeve  4 Different Adjustments

Adams CMX® Adjustable Sleeve 4 Different Adjustments

   We at Billy Bob’s Developed a Aftermarket Adjustable Sleeve,  CMX®  that fits the Adams Old and New line of Drivers, it fits the Adams Fast Speedline Tech, the Super LS Speedline, Super S Speedline, it is different than the Factory sleeve. We made Four Different Sleeves with Three Different Adjustments;    2o (Standard),   3o and 4o

They are all interchangeable and will fit all the Speedline Drivers.  You can make that old Speedline Tech or the New Super S  from  8o to 12o Driver. We made them in Red to match the Red on the Driver Head…. Looks Cool! ....We make all our sleeves here in the USA.

Available in R-H or L-H .335 and .350

 

 

TECH335RH

$25.00 (save 17%)

Billy Bob's CMX® A-Fit Adaptor Fits The Ping Anser Driver & Woods & G25

Billy Bob's CMX® A-Fit Adaptor Fits The Ping Anser Driver & Woods & G25

The New Ping Anser Driver and Fairway Woods and G-25 are now on the market, we at Billy Bob’s have come up with a CMX A-Fit Aftermarket Sleeve that will fit the Anser Drivers and Woods.
We made them different than the OEM, they are a bit Longer in Length with more shaft insertion, and with 3 Different Adjustments: Plus or Minus ¼ Degree, a Plus or Minus ½ Degree Adjustment (standard) and a Plus or Minus ¾ Degree Adjustment, and a Full 1o Degree..... they are available in .335 and .350 R-H and L-H Versions. So now you have many different variations of Adjustment

Ping is a Register Trademark

CMX A-FIT33514

$25.00 (save 17%)

Ping  i-20 i-25 , S-56 Iron Ferrules

Ping i-20 i-25 , S-56 Iron Ferrules

The New I-20 Iron are here…. and Ping has done it again.   There is no ferrule out there that will work . It has a 5/16 “ counter bore with windows for glue expansion and a .355 I.D for taper tip shaft replacements .

We at Billy Bob’s have come up with the proper replacement Ferrule  … that is what we do.. ENJOY!!!

These Ferrules will fit  I-20 Irons, the S-56 Irons and the Anser Irons they are Available In  Black Or Ghost Ferrule™ 

 

PING-I-20

$1.50 (save 40%)

Billy Bob's Color Ferrules. Deep, Bright Colors

Billy Bob's Color Ferrules. Deep, Bright Colors

Billy Bob’s New Colored Ferrule Line: Add “A” Lot More Color to Your Game!!! All of our Ferrules are Made with Our Own Injected Molds Here in the U.S.A, They are not turn on CNC Machines in China. We use Butyrate and not Cellulose Acetate which is softer and not of good Quality. Our colors are Deeper and Brighter and, of Exceptional Quality.
 
Only Billy Bob's give you this many colors and sizes to choose from.

NCF33534-DPINK

$0.57

Billy Bob's Colored Ferrule Kits up to 600 pieces

Billy Bob's Colored Ferrule Kits up to 600 pieces

Billy Bob's Colored Ferrule Kits

We have taken our entire Colored Ferrule Line and built up 2 Colored Ferrule Kits

For Drivers and Woods .335 3/4" tall all Fifteen Colors 10 each. 

For Drivers and Woods .350 3/4" tall all Fifteen Colors 5 each.

Total 240 Pieces.

 

For Irons .355 3/4"  Taper Tip tall all Fifteen Colors 12 each. 

For Irons .370 Parallel Tip 3/4" tall all Fifteen Colors 12 each.

Total 360 Pieces.

 

3033KIT-DW

$110.00

Ping i-20, i-25, S-56, and Anser Irons Ghost Ferrules™

Ping i-20, i-25, S-56, and Anser Irons Ghost Ferrules™

The New Anser Iron are here…. and Ping has done it again.   There is no ferrule out there that will work . It has a 5/16 “ counter bore with windows for glue expansion and a .355 I.D. for taper tip shaft replacements .

We at Billy Bob’s have come up with the proper replacement Ferrule.

These Ferrules will fit  I-20 Irons, the S-56 Irons and the Anser Irons they are Available In  Black Or Ghost Ferrule™ 

 

PING-ANSER

$1.50

Silver Ring Ferrules in Black or White

Silver Ring Ferrules in Black or White

Billy Bob's Silver Ring White and Black Ferrules

We've had many requests for a White Ferrule with Silver Rings,  and also a Black Ferrule with with Silver Rings, with special outside diameters. Again we have listened to your needs and we are now producing these in the following sizes

1/2" .335 ID Parallel x 520 OD

1/2 .335 ID Parallel x  520 OD

3/4" .350 ID Parallel Tip x 560 OD

3/4" .360 ID Taper Tip x 560 OD

3/4" .370 ID Parallel Tip x 560 OD

NCF33512-G-2

$0.45 (save 10%)

Fluted Ferrule  .335 ID  .630 OD for Callaway FT-i Z Driver, Diablo Edge, and Razor Hawk

Fluted Ferrule .335 ID .630 OD for Callaway FT-i Z Driver, Diablo Edge, and Razor Hawk

Callaway Golf has come out with the FT-iz Driver, This will fit the current FT-iz Driver, Diablo Edge Driver, and the New Razor Hawk Driver

it has the largest outside diameter of any ferrule on the market. There is nothing you can use that will give this head a factory finish like the original, the outside diameter is .630. We at Billy Bob's have developed a ferrule like our original .335 Universal adaptor but with a larger .630 outside diameter, this will cover the top of the Hosel.

Eventually your Customers will will come into your shop with this New Club to have the shaft replaced or repaired... " Will you have the necessary Ferrule and adaptor to Fix His or Her Club" ? ...YOU WILL NOW!


*Note: You can now take a .350 FT-iZ driver and use a .335 Shaft like the more expensive FT-iZ Tour model.

FTIZ-D335

$5.00

Nike STR8-Fit Ferrule Dymo, VR

Nike STR8-Fit Ferrule Dymo, VR

Nike STR8-Fit Ferrule Adapter

   When this club comes into your shop be ready with the Billy Bob's Replacement Ferrule for the Nike Adjustable Sleeve. Billy Bob's Golf has once again made the frustrating job of finding the correct ferrule; so you can give your customers that Professional Factory - Finished Quality in your own shop.

     *Nike is a Registered Trademark

  ** The VR Series requires a slight modification for this to fit properly

  Nike STR8-Fit Ferrule PDF Manual 


 

NIKE-STR8-FER

$8.00

Metal Sleeve Kit for Cobra  S2, S3, ZL Adjustable Woods

Metal Sleeve Kit for Cobra S2, S3, ZL Adjustable Woods

 With the Billy Bob Adjustable Sleeve you will still be able to make the same factory adjustments...3 positions= Open, Closed, and Neutral. 

  We then made the sleeve to fit our Complete line of Adaptors and Ferrules along with our loft and lie ferrule you will be able to Dial-in (Clock) any changes to the loft and lie,  up Appox to 2 degrees, within a 360 degree rotation, also increasing the open and close position as well. This will give you many more options than the Factory Club.

 

See the COBRA S2 Instructions HERE

COBRA SLEEVE KIT

$30.00 (save 25%)

CMX® Threaded Top Metal Ferrule (Fits All Bottom Sleeves)

CMX® Threaded Top Metal Ferrule (Fits All Bottom Sleeves)

This is the CMX® Threaded Metal Ferrule that attaches to the CMX® OEM Bottom Sleeve and the Universal Straight Fitting System.

Available .335, .350, .355 & .370  (Irons only)  sleeve sold seperately

R-H or L-H

CMX-FIT TOP FERRULE 335RH

$14.00 (save 7%)

CMX® Fittting System Taylor RBZ Stage 2, SLDR, JetSpeed, Adams XTD

CMX® Fittting System Taylor RBZ Stage 2, SLDR, JetSpeed, Adams XTD

We at Billy Bob’s have seen many different Club Fitting Systems, some good and some not so good. As a result, we came up with a system that will give you the closest specifications to a Regular, Permanently Epoxied Shaft. The reason this works is that the shaft goes down through to the bottom of the hosel sleeve and the shaft is attached to the sleeve with our Patent Pending CMX® Threaded Top Ferrule System. (This will come with a complete set of instructions). We start out with our Billy Bob’s CMX Aftermarket Adjustable Sleeves that fit TaylorMade RBZ Stage 2, SLDR, JetSpeed, Adams XTDTi. Next, we manufactured a CMX® Threaded Metal Ferrule that is epoxied to the tip end of the shaft that fits within the sleeve. Now, you can have unlimited shaft combinations . This creates a huge advantage in club fitting, all while being extremely cost effective. We will offer these CMX® Sleeve Bodies and the CMX® Threaded Metal Ferrule that can be purchased Separately based on the fitter’s needs. This is for the CMX® TaylorMade RBZ Stage 2, SLDR, JetSpeed, Adams XTD Ti

CMX FITTING SYSTEM RBZ 2 LH

$29.00 (save 17%)

CMX® Fitting System Titleist 910, 913 Drivers (Sleeve Sold Separately)

CMX® Fitting System Titleist 910, 913 Drivers (Sleeve Sold Separately)

We at Billy Bob’s have seen many different Club Fitting Systems, some good and some not so good. As a result, we came up with a system that will give you the closest specifications to a Regular, Permanently Epoxied Shaft. The reason this works is that the shaft goes down through to the bottom of the hosel sleeve and the shaft is attached to the sleeve with our Patent Pending CMX® Threaded Top Ferrule System. (This will come with a complete set of instructions). We start out with our Billy Bob’s CMX Aftermarket Adjustable Sleeves that fit Titleist 910 1nd 913 drivers. Next, we manufactured a CMX® Threaded Metal Ferrule that is epoxied to the tip end of the shaft that fits within the sleeve. Now, you can have unlimited shaft combinations . This creates a huge advantage in club fitting, all while being extremely cost effective. We will offer these CMX® Sleeve Bodies and the CMX® Threaded Metal Ferrule that can be purchased Separately based on the fitter’s needs.This is for the CMX® Titleist Sleeve Bottom Body only.

CMX FITTING SYSTEM TITLEIST RH

$29.00 (save 17%)

CMX® Fitting System Ping Anser & G-25 Drivers (Sleeve Sold Separately)

CMX® Fitting System Ping Anser & G-25 Drivers (Sleeve Sold Separately)

We at Billy Bob’s have seen many different Club Fitting Systems, some good and some not so good. As a result, we came up with a system that will give you the closest specifications to a Regular, Permanently Epoxied Shaft. The reason this works is that the shaft goes down through to the bottom of the hosel sleeve and the shaft is attached to the sleeve with our Patent Pending CMX® Threaded Top Ferrule System. (This will come with a complete set of instructions). We start out with our Billy Bob’s CMX Aftermarket Adjustable Sleeves that fit Ping Anser & G-25 Drivers. Next, we manufactured a CMX® Threaded Metal Ferrule that is epoxied to the tip end of the shaft that fits within the sleeve. Now, you can have unlimited shaft combinations . This creates a huge advantage in club fitting, all while being extremely cost effective. We will offer these CMX® Sleeve Bodies and the CMX® Threaded Metal Ferrule that can be purchased Separately based on the fitter’s needs. This is for the CMX® Ping & G-25 Sleeve Bottom Body only.

CMX FIT PING RH

$29.00 (save 17%)

CMX® Fit System Callaway Razr Fit,Opti Fit,Opti Tour X-Hot Bottom Sleeve

CMX® Fit System Callaway Razr Fit,Opti Fit,Opti Tour X-Hot Bottom Sleeve

We at Billy Bob’s have seen many different Club Fitting Systems, some good and some not so good. As a result, we came up with a system that will give you the closest specifications to a Regular, Permanently Epoxied Shaft. The reason this works is that the shaft goes down through to the bottom of the hosel sleeve and the shaft is attached to the sleeve with our Patent Pending CMX® Threaded Top Ferrule System. (This will come with a complete set of instructions). We start out with our Billy Bob’s CMX Aftermarket Adjustable Sleeves that fit Callaway Razr Fit, X Hot, Opti Fit, Opti Fit Tour, Razr Fit Tour.  Also you have the option to select which Collar you may want. 1 Degree (OEM version), or 2 Degree (CMX our version) or the Tour Collar 1.2 Degree,  all will fit this sleeve.

Next, we manufactured a CMX® Threaded Metal Ferrule that is epoxied to the tip end of the shaft that fits within the sleeve. Now, you can have unlimited shaft combinations . This creates a huge advantage in club fitting, all while being extremely cost effective. We will offer these CMX® Sleeve Bodies and the CMX® Threaded Metal Ferrule that can be purchased Separately based on the fitter’s needs. This is for the CMX® Callaway Razr Fit, X Hot, Opti Fit, Opti Fit Tour, Razr Fit Tour.

CMX FITTING SYSTEM RH 1o Collar

$29.00 (save 17%)

CMX® Fitting System TaylorMade R1 (Bottom Sleeve Sold Separately)

CMX® Fitting System TaylorMade R1 (Bottom Sleeve Sold Separately)

We at Billy Bob’s have seen many different Club Fitting Systems, some good and some not so good. As a result, we came up with a system that will give you the closest specifications to a Regular, Permanently Epoxied Shaft. The reason this works is that the shaft goes down through to the bottom of the hosel sleeve and the shaft is attached to the sleeve with our Patent Pending CMX® Threaded Top Ferrule System. (This will come with a complete set of instructions). We start out with our Billy Bob’s CMX Aftermarket Adjustable Sleeves that fit TaylorMade R1. Next, we manufactured a CMX® Threaded Metal Ferrule that is epoxied to the tip end of the shaft that fits within the sleeve. Now, you can have unlimited shaft combinations . This creates a huge advantage in club fitting, all while being extremely cost effective. We will offer these CMX® Sleeve Bodies and the CMX® Threaded Metal Ferrule that can be purchased Separately based on the fitter’s needs. This is for the CMX® TaylorMade R1

CMX FITTING SYSTEM R1 4o RH

$29.00 (save 17%)

CMX® Fitting System Counter Balance Weight Kit

CMX® Fitting System Counter Balance Weight Kit

These small weights are pushed in the hole at the Butt End of the Grip.

They are helpful in counter balancing swing weight for a launch monitor or for fitting purposes.

Note*  You may have to drill a small hole in the grip as some manufactures don't have the hole go all the thru the Butt End of the grip.

Avail:  2,4,6,8 grams

 

CMX COUNTER BALANCE GRIP WEIGHTS

$38.00