The Shaft Used By the 2019 Long Drive Champion Kyle Berkshire
LD 70, LD 60+, LD 50, LD 30+, LD 20, Mid-High Balance point, High kick point advanced composite table rolled construction that kicks hard and recovers fast in a tailored sequence from butt to high tip. Producing increased ball velocity and a Medium height piercing shot trajectory.
See Complete Descriptions, Spec. Below
Long Drive Series 48″
Featuring Dual-flex reactive technology, in the world only pre-loaded, and vacuum-cured Nano-Carbon amorphous fiber material shaft construction, table rolled laminate composite. Vacuum Cured to minimize resin content, optimizing elastic strength and dynamic recovery properties of the Nano-Carbon Amorphous material. Enhancing feedback and delivering an extremely forgiving shaft. Active butt and tip quadrants are tailored for high-speed long-drive athletes desiring to improve efficiency and increase ball velocity through the purest kinetic energy transfer from the golfer to the club.KVMT70-BGBLD is a Mid-High Balance point, High kick point advanced composite table rolled construction, that kicks hard and recovers fast, in tailored sequence from butt to high tip. Producing increased ball velocity and a Medium height piercing shot trajectory.
Flex Code | Torque ±0.5° | Tip dia. ±0.002” (±0.05mm) | Tip/par ±0.5″ | Butt dia. ±0.005” (±0.12mm) | Butt par. ±0.5″ | Length | Weight ±2g | Frequency ±5cpm | Balance point | Kick point | Materials |
(205g Tip weight) | |||||||||||
LD70 | 4.5° | .335” (8.50mm) | 4.00″ | .638” (16.20mm) | 9.50” | 48.00” | 72g | 295cpm | 55.00% | High | Amorphous, 40T, 30T,5T |
LD60+ | 4.5° | .335” (8.50mm) | 4.00″ | .638” (16.20mm) | 9.50” | 48.00” | 71g | 275cpm | 54.00% | High | Amorphous, 40T, 30T,5T |
LD50 | 5.5° | .335” (8.50mm) | 4.00″ | .630” (16.00mm) | 9.50” | 48.00” | 66g | 265cpm | 53.00% | High | Amorphous, 30T, 5T |
LD30+ | 5.7° | .335” (8.50mm) | 4.00″ | .622” (15.80mm) | 9.50” | 48.00” | 61g | 245cpm | 52.00% | High | Amorphous, 30T, 5T |
LD20 | 5.9° | .335” (8.50mm) | 4.00″ | .618” (15.70mm) | 9.50” | 48.00” | 58g | 225cpm | 51.00% | High | Amorphous, 30T, 5T |
CPM Parameters:
Shaft type | Tip weight | Clamp length | Clamp pressure |
Long Drive | 205g | 4.50” | 4kg cm² |
- All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
- Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
- Please do not Chamfer the tips; however, light belt abrasion is recommended .*Tip preparation: light belt abrasion or hand sanding is recommended prior to final assembly.*To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will, in many assemblies, be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to ensure a full shaft insert and adequate epoxy adhesion. Do not use the Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.
- Shaft Model: LD 70 | LD 60+ | LD 50 | LD 30+ | LD 20
- Shaft Flex: LD20 R Flex | LD30 S Flex | LD30+ SS Flex | LD50 2X Flex | LD60 3X Flex | LD60+3X Tour Flex | LD70 4X Tour Flex
- Shaft Color: Black/Pink | Black/Red | Electric Blue/Red | Green | Midnight Gold | Sky Blue/Red